carbody

removal of the door pillar trim

Remove :

• The door seal Je which covers the pillar.

• The fastening clips Cl.

• The door pillar trim Cm.

Clear it by pulling upwards.

removal of the door pillar trim

Airbag fitted vehicle on the passenger side :

Extract :

• The door seal Je which covers the pillar.

• The fastening clip Cl.

Put aside :

• The door pillar trim Cm.

Extract :

• The trim clip Ag.

With pliers :

Rotate about 90° the trim clip Ag.

Free the pin Er from the groove.

sun visor removal

Lift up :

• The access covers Cs.

With pliers Ot :

Free the springs Cr and remove the handle Po / left side / right side.

Remove :

• The covers Cs using a screwdriver.

• The fastening Vs screws.

• The sun visor bearing Pa.

• The sun visor Ps.

Rotate about 90°°.

Remove :

• The central sun visor bearings Pa.

Put aside :

• The moulded headlining.

dome light removal

Unclip :

• The fastenings * with the help of a convenient Ot tool.

• The dome light Pj.

Disconnect the connector.

rearview mirror removal

Rearview mirror / standard:

Extract :

• The covers Cs.

Push the lever Le , then have the rearview mirror Ro glide and remove it -> upwards.

rearview mirror removal

Electrochromic rearview mirror / with lane assist warning:

Remove :

• The lane assist warning sensor - camera.

Unclip :

• The covers Cs.

• Disconnect the connector.

Remove :

• The fastening screw Vs.

• The rearview mirror Ro -> downwards.

Rearview mirror with rain sensor:

Remove :

• The covers Cs.

Disconnect :

• The connector Co.

Pull :

• The fastening endstop Vr -> downwards.

Extract the rain sensor Cp from the retaining plate Pu -> downwards.

rain sensor reassembly

Before the reassembly :

Remove :

• The former self-adhesive film from the rain sensor Cp.

Apply the new protective film Ad on the rain sensor Cp -> with double-sided tape.

a distance 7,5 mm.

b distance 13,5 mm.

reassembly of the lane assist camera

Extract :

• The access covers Cs1.

Unlock :

• The fastenings * / in that order 1 2.

Extract :

• The access covers Cs2.

Unlock :

• The fastenings *.

Let  Cs2 glide / downwards ->.

Disconnect the connectors Co.

Remove :

• The rearview mirror.

.

Unlock :

• The safety hooks Cr 1.

Clear :

• The holding guides Gn rearwards 2.

Extract :

• The retaining bracket Pu.

Remove :

• The assist camera Cam.

Clear :

• The holding guides Gi out of the windscreen base Su rearwards ->.

reassembly of the lane assist camera

Unclip / extract:

• The connector Co.

Free the clamps ->.

Unclip the wiring harness.

Unlock :

• The fastenings At.

Extract :

• The clips Ag.

Extract :

• The light-masking screen Ca.

After reassembling :

Proceed to reset the movie camera with the diagnosis tool and other necessary tool.

reset

reset

Standard procedure :

• Static calibration / calibration in 3 step.

Method(s) :

1 prerequisites.

• Proper tyre pressure.

• Empty (unloaded) vehicle.

• Fuel tank full.

2 wheel alignment in proper order.

• Check that no alignment or drive train defects are reported.

• Abnormal wear and tear of the tires.

• No slipping occuring in the vehicle's trajectory.

• Steering wheel aligned for straight line driving.

3 place the vehicle in front of the calibration's aiming panel Ot.

• Measure the vehicle's width.

• Affix vertical strips 1 / 2, in order to draw reference points x1 x4 on the ground.

• Do a projection of the center point x1 x4 on the ground with a plumb line Ot2.

• Draw a line on the ground in the reference axis x1x4 in order to align the aiming panel Ot.

• Draw a straight line x3 , perpendicular to the axis x1x2, located approximately c from the ground projection of the point x1.

.

Nota :

c distance between the point x1 and the ground position B of the aiming panel.

• c distance 1316 mm.

.

• Draw the point B at the cross between axis x1x2 and x3.

• Draw on each side repectively the points C D at a given distance b.

• b 550 mm distance.

Nota :

b floor distance between the aiming panels locations B C/D.

• Place the aiming panel Ot at the point B.

• Align the vehicle axis x1x2 in the axis of the aiming panel Ot.

• Adjust / center height of the aiming panel a Ot.

Nota :

Distance a between the ground and the aiming panel center Ot.

• a distance 1350 mm.

reset

Method(s) -> ...cont.:

4 use a diagnosis equipment.

• Step 1.

• Observe the distances A between the vehicle and the aiming panel Ot -> camera Cam.

• A distance 3000 mm.

• Step 2 -> reset.

• -> use a diagnosis equipment / display the " -> " menu.

• Chassis / Front Recognition Camera / utility / Recognition Camera / Target Position Memory.

5 key-in the data of the calibration distances in the diagnosis equipment.

Nota :

According to the assist options handled by the front camera, the following parameters will require key-in at each step.

• Chassis code -> see vehicle I.D. plate.

• Height of the camera 1288 mm.

• Side setting of the camera 7 mm.

• Yaw rate angle 0 ° Deg.

• Inclination angle -2,42°.

• Center height of the aiming panel 1350 mm.

• Distance between aiming panel and camera 3000 mm.

• Interval between the aiming panel patterns 550 mm.

• Height of aiming panel patterns 180 mm.

• Vehicle's width 1832 mm.

• Distance between center axis of the rims and camera 735 mm.

• Height variation angle 0 ° Deg.

• Distance between radar and camera 1625 mm.

6 calibration in 3 step.

• Use a diagnosis equipment / display the " -> " menu.

• Chassis / Front Recognition Camera / utility / Recognition Camera Axis Adjust.

During the sequential learning in 3 time.

• Move the aiming panel between the locations 1 2 -> C 3 -> D at each validation step by the calibration equipment.

7 make a roadtest.

windscreen tools

• Standard tools.

specific windscreen tools

• Nothing.

tools for accessories

• Nothing.

ingredients

• Standard bonding kit ( glue - glass/metal primer - activator - solvent ).

waterbox accessibility

Remove :

• The wiper arms.

• The gasket of the waterbox.

• The clips -> Ag.

• The waterbox adornment Ej / right side / left side.

• The clips -> Ag x3.

• The fastenings At x12.

• The cover of the waterbox Ct.

reassembly : accessories of the waterbox

Put back :

• The cover of the waterbox Ct on the housing frame.

• The gasket Je of the waterbox and the wiper Be.

outer moulding removal

Unclip :

• The side mouldings Ba of the roof pillars.

particular instruction

outer moulding removal

Remove / cut:

• The upper border profile Pm.

gasket cut

Because of the fastening shims Ca, the seal cutting - with a cutting wire Fl - should follow the pattern shown.

particular instruction

The glass is serigraphied with reference marks on the ceramic Cy to align properly the position shims (endstops) Caf during the set-up procedure.

Set-up the upper endstops Cas on the rebate Fe.

.

Apply a light layer of glass primer Cr on the windscreen flank.

a2 distance 82 mm.

b2 distance from the edge 24 mm.

Bond the endstops Caf as shown between the marks Cy on the windscreen / right side / left side.

.

a distance from the edge 14 mm.

b spacing from the center marking on the ceramic strip Cy 40 mm.

particular instruction

Standard version :

Using some primer, bond the upper profile Pm on the windscreen prior to the windscreen bonding.

• c distance from the edge 7 mm.

specific windscreen bonding

Use a primer on the ceramic Cr prior to bonding.

Cr width 18 mm.

Place a spacer tape on the perimeter Bs of the windscreen Pb.

Bs length / full refill quantity (L) 295 cm.

Bond and align the axis of the perimetric spacer Bs on the lower part of the windscreen, following the reference line C shown on the glass.

Markings Rp are serigraphied on the glass, in order to align the ends of the spacer tape Bs.

Stick :

• The profile Pm2 fastening the waterbox cover.

Nota :

Align the marks Rp2.

Adjust the windscreen Pb clearance a / lower border profile Pm2.

a width 0,6 mm.

Bond setting :

Place the bond seal Jc close to the spacer tape Bs, as shown.

specific windscreen bonding

The area Jc where the glue bead is applied is delivered not being previously pasted, neither by an undercoat nor by a glass-primer.

The serigraphied area Cr where the glue bead is to be applied should be at first coated with primer.

specific windscreen bonding

According to the mounting :

The windscreen is serigraphied with a central line X upon the perimeter of the edge.

Apply the bond seal Jc upon the serigraphied points of the reference bonding line X.

Distance from the edge :

a width 8 mm.

b width 8 mm.

c width 11 mm.

d width 9 mm.

In order to intertwine the seal at the end of the perimeter, apply a double bonding.

d2 width 19 mm.

Nota :

The bond seal Jc should superimpose and gently overlay the profile Pm in order to allow its adherence when put in its place.

specific windscreen bonding

Glue bead: cross section > bevel.

a width 8 mm.

b height 12 - 14 mm.

In order to intertwine the seal at the end of the perimeter, apply a double bonding.

Place the bond seal Jc close to the spacer tape Bs, as shown.